亚洲va中文字幕欧美不卡-亚洲va在线va天堂成人-亚洲va在线va天堂va手机-亚洲va在线va天堂va888www-久一视频在线-久污tv

Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

News



Tel:(0755)27151698
Fax:(0755)27150611
Mailbox:szzyzcl@163.com / szzy@szzy99.com
Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
Industry information

當前位置:

首頁 News Industry information

Causes and solutions of top whiteness in injection molding products

Release time:2021-08-16

When the plastic parts of injection products are ejected from the mold, if the ejector pin is used, the ejector rod will often leave deep or shallow marks on the plastic parts. If these traces are too deep, the so-called top white phenomenon will appear. In serious cases, the so-called top explosion will occur when the plastic parts are pushed through.


The main reason for the whiteness of plastic parts is that the product has a large mold adhesion force, and the ejection part on the plastic parts causes white marks at the ejection part of the ejector rod. The specific reasons and improvement methods are as follows:


1. Back mold temperature is too low or too high: adjust the appropriate mold temperature.


2. Too fast ejection speed: slow down the ejection speed.


3. With demoulding chamfer: overhaul the mold (polishing).


4. The ejection of finished products is unbalanced (the ejection leaf spring is broken): repair the mold (make the ejection balanced).


5. Insufficient number of thimbles or improper position: increase the number of thimbles or change the position of thimbles.


6. Vacuum occurs in the mold during demoulding: clean the dirt in the ejector pin hole to improve the air inlet effect.


7. The finished bone and column positions are rough (inverted): polish each bone and column position.


8. High injection pressure or holding pressure: reduce the pressure appropriately.


9. The demoulding angle of the finished mold is too small: increase the demoulding angle of the rear mold.


10. Improper action time or position of side slider: repair the mold (make the core pulling action normal).


11. Ejection area is too small or ejection speed is too fast: increase the ejection area or slow down the ejection speed.


12. The injection speed of the last section is too fast (Burr): slow down the injection speed of the next section.


These are the reasons and solutions for the whitening of injection molded products.

Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
主站蜘蛛池模板: 欧美亚洲专区 | 天堂bt资源在线官网 | 十八毛片 | 日韩欧美在线视频 | 日本五级床片午夜视频 | 中文字幕伦伦在线中文字 | 亚洲无毛 | 欧美一级片手机在线观看 | 一级做a爱片久久毛片 | 日本大片成人免费网址 | 日韩在线视频线视频免费网站 | 日本激情视频在线观看 | 香蕉成人福利片视频在线下载 | 欧美一区在线播放 | 日日噜噜噜夜夜爽爽狠狠 | 天天色亚洲 | 日本高清免费不卡在线播放 | 色欧美亚洲 | 无码中文字幕乱在线观看 | 亚洲婷婷丁香 | 日本三级成人午夜视频网 | 日韩在线第二页 | 天天色综网| 收集最新中文国产中文字幕 | 色欧美在线视频 | 亚洲精品在线第一页 | 亚洲www网站| 天天插天天透天天狠 | 日韩精品久久久毛片一区二区 | 欧美一卡2卡3卡四卡海外精品 | 婷婷久久综合网 | 伊人四虎 | 中文字幕视频一区二区 | 色噜噜色噜噜天天拍一拍 | 四虎影院在线免费播放 | 日产国产欧美韩国在线 | 日韩专区亚洲国产精品 | 天天逼逼 | 五月天激情婷婷 | 亚洲视频在线观 | 中文字幕国产 |